Memsic
Hall switch
2.5 µA typical, 1.65 to 5.5 V, DFN4 package at 1.0 x 1.4 mm. Unipolar and omnipolar outputs.
- MHA100KN
- MHA182AS-S
- MHA183AS

Overview
Memsic's Hall switches combine a Hall sensor and its switching circuit on one low-power CMOS chip, with built-in sensitivity and temperature compensation. They draw about 2.5 µA typical at 1.8 V and run from 1.65 to 5.5 V, which suits always-on lid and cover detection in battery devices. Parts are offered in DFN4, SOT23 and SOT553 packages with unipolar or omnipolar outputs.
Built for
- TWS earbud charging case lid detection
- Laptop and tablet cover switches
- Smart meters
- Wearables and domestic appliances
Key features
Ultra-low power
Supply current is 2.5 µA typical and 5 µA maximum at 1.8 V.
Wide supply range
Operates from 1.65 to 5.5 V.
Small packages
The MHA100KN comes in a 1.0 x 1.4 x 0.37 mm DFN4, with SOT23 and SOT553 options in the MHA18x series.
Defined hysteresis
A hysteresis window of a few gauss keeps the open and close switch points consistent.
Output options
Parts cover dual N/S output, single S-pole unipolar and omnipolar push-pull output.
RF noise immunity
Good RF noise immunity for use near radios.
Specifications
- Technology
- Hall effect, low-power CMOS
- Supply voltage
- 1.65 to 5.5 V
- Supply current
- 2.5 µA typ, 5 µA max at 1.8 V
- Operate point (BOP)
- 37 G typ
- Release point (BRP)
- 30 G (MHA100KN), 27 G (MHA18x) typ
- Wake period
- 50 ms typ
- Output modes
- Unipolar, omnipolar, dual N/S
- Packages
- DFN4, SOT23, SOT553
- Operating temp
- -40 to +85 °C
Part numbers (link to datasheets)
| Part | Polarity / output | Operate / release (typ) | Supply | Current (typ) | Package | Notes |
|---|---|---|---|---|---|---|
| MHA100KN | Dual output, N and S pole (omnipolar) | 37 G / 30 G | 1.65 to 5.5 V | 2.5 µA at 1.8 V | DFN4 1.0 x 1.4 x 0.37 mm | Separate N and S outputs |
| MHA182AS-S | Single output, S-pole unipolar, push-pull | 37 G / 27 G | 1.65 to 5.5 V | 2.5 µA at 1.8 V | SOT553 1.2 x 1.6 x 0.5 mm | ESD HBM ±3.5 kV |
| MHA183AS | Single output, omnipolar, push-pull | 37 G / 27 G | 1.65 to 5.5 V | 2.5 µA at 1.8 V | SOT23 2.9 x 1.6 x 1.1 mm | ESD HBM ±4.5 kV |
Specifications as published by Memsic. Configurations vary by model, so we will confirm the exact build with your quote.
Buying the Hall switch in India
Authorised Memsic distributor
Genuine Memsic products, sourced directly from Memsic.
GST invoice
Invoiced in India with GST, so registered businesses can claim input tax credit.
From stock or to order
Some products ship from our stock in India, and we order the rest from Memsic for you.
Help choosing
Tell us the application and we will recommend the right Memsic product.
More from Memsic
All Memsic products
AMR magnetometer
Higher accuracy to 1°, low noise and low temperature drift. SET and RESET coils degauss without frequent recalibration.
- MMC5616WA-E
- MMC5983MA
- MMC5603NJ
- +3 more

Thermal accelerometer
A gas mass instead of a moving one: Passes every drop test, ignores high frequency vibration, and holds its zero g offset through SMT.
- MXC4005XC
- MXC6655XA
- MXR7150VW
- +4 more

Capacitive accelerometer
Monolithic CMOS design in packages from 1.6 x 1.6 mm, with sniff and ultra low power wake modes.
- MXC3638AL
- MXC3500AL
- MC3419
- +5 more

6 axis IMU
3 axis gyroscope plus 3 axis accelerometer with large FIFO, I2C, I3C and SPI, output to 2,200 Hz.
- MIC6102AL

eOIS controller
One chip optical image stabilisation driver: Linear Hall sensor, H bridge and PID in a 6 pin WL-CSP.
- MSD4100WA
Need help choosing?
Tell us your application. We will recommend the right Memsic product, quote it and support it after delivery.